Showing posts with label fix. Show all posts
Showing posts with label fix. Show all posts

Thursday, December 27, 2012

103 metrakit kit port match to teknix case

Continued from 103 polini seizure. I'mma hack this kit to this case.


See the marks from where the old kit transfers were?



1 wurd: blowtorch.

See them little flecks of metal?

That's one there.
And another.

Masking tape to keep metal out of the seal.

yuk.


oh yeah lookit that sludge.

Ok here we go:
Gettin' there.
Oh yeah she oughta breathe good now.




 What a nice ignition.


 
Ever give a motor a blowjob? Fun explaining that one on the invoice....


 
Time to go back on the bike.

Fired right up. Tuning notes as follows:
Teknix cases matched to 64cc metrakit polini head carbon fiber Malossi 4 petal reed block & intake, Dellorto PHBG pilot: 40 main: 100 W7 needle leanest notch simonini circuit two ball vari stock 12v  NOS peugeot points sys pulls hard chickened out speedo read past 120 km/h, so that's at least 60, right? zowie....pipe seems pretty decent - not too peaky.

00138 CL 175


Ignition switch needs some wires & connectors replaced, and the battery was totally dry & must be replaced. A traditional lead-acid battery like the original is about $35. Depending on atmospheric conditions, they lose electrolyte through the breather tube and distilled water and acid must be added. If the fluid level or the charge drop too low, the battery is ruined. I highly recommend using a sealed battery, even though they are around $75, they last a lot longer because they don't evaporate electrolyte, hold a charge better, and often are warranted for a couple of years. When the ignition switch was bypassed and a spare battery used, I could hear the ignition solenoid go "click," which means it's working. It fired up and ran on one cylinder. Could be a new battery is all it needs for the electric starter to work, although I noticed the turn signals didn't work, and a couple of loose wires. I'd be surprised if there weren't a few other shorts. Condensers could need replacing as well, but those are cheap. Did the bike run better cold and then do worse as it warmed up? The petcock had some rusty sludge in it and wasn't draining well. I took it apart and blew some compressed air through it and it works fine now. The screen for the reserve is missing and should be fixed sooner than later, or else sediment will pile up in there again. The #2 carb seems to not be getting gas, although the float seems to be functioning.

Hotwired.



Lotsa rusty sludge.


Carb on right is dry.

No sludge!


One of the spark plugs was a extended reach plug, which caused the electrode tip come into contact with the piston head. Fortunately, this simply bent the tip of the electrode. After carb and wiring rebuild & setting all tolerances to spec, the bike fired up. It ran on both cylinders, but one kept losing spark. This was narrowed down to a short in the spark plug cable. I replaced the ignition coil and broken tail light with parts from a CB750. The battery was replaced with a sealed unit, a Power Source WP9-BS. Pulls great at 6-7k (Red line @ 10.5k!) with a wonderful throaty exhaust note - brash but not obnoxious. Suprisingly gentle clutch. Bike is beat but has a lot of life left to it and even more character. 

 

Saturday, December 8, 2012

00137 Honda 1980 C70 Passport / Cub

Phil's got my old Aermacchi, but I'm currently tuning his Honda Passport C70. Aka the Cub, it is the most common motorbike on the planet. This one was not idling at low revs, despite having the carb cleaned. On inspection, the bamboo points armature that is actuated by the cam on the flywheel had worn down to such a degree as to not open the points. This was resolved by simply adjusting the points. The oil centrifuge was de-sludged, and the gaskets replaced. Battery, though it holds a charge, probably doesn't have much life left to it. I'd have liked to take a look at the tappets, but the damn covers are seized to point where removing them would destroy the covers and possibly the threads on the head, so that's just not gonna happen. 


Now you see the engine.
Now you don't.





Sludge...wish I could get my guitar to sound like that looks.


 Pretty clean.

 Oil pump is fine.


 clean enough to pour oil on.
3rd world manufacturing














 Screwed into the case half...pretty ingenious design, so des ne?
On to the points! 


Points aren't moving. That there's your problem.
 Melted and corroded and generally non-conductive around the ignition and the electric starter circuits.


 Many hours later: